Complaints & Recalls
Official Safety Recalls - Important!
9 RecallsThese are official manufacturer recalls ordered by NHTSA for safety defects. If you own this vehicle, contact your dealer immediately for free repairs.
Chrysler (fca Us, Llc)
Safety Issue:
Chrysler (FCA US, LLC) is recalling certain 2020-2024 Jeep Gladiator and 2018-2024 Jeep Wrangler vehicles. The instrument panel cluster may experience an internal short circuit and fail. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 101, "Controls and Displays."
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Mfg Campaign: 30B
Recall Date: Sep 5, 2024
Chrysler (fca Us, Llc)
Safety Issue:
Chrysler (FCA US, LLC) is recalling certain 2021 Jeep Wrangler and Jeep Gladiator vehicles that were previously remedied under NHTSA recall number 23V-116. The software for the powertrain control module may cause an engine stall, which can result in a loss of drive power.
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Mfg Campaign: 92B
Recall Date: Aug 1, 2024
Chrysler (fca Us, Llc)
Safety Issue:
Chrysler (FCA US, LLC) is recalling certain 2021-2023 Jeep Wrangler, Gladiator, and 2022-2023 Ram 1500 vehicles equipped with a 3.0L diesel engine. The high pressure fuel pump (HPFP) may fail.
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Mfg Campaign: 01A
Recall Date: Apr 13, 2023
Chrysler (fca Us, Llc)
Safety Issue:
Chrysler (FCA US, LLC) is recalling certain 2018-2023 Jeep Wrangler, and 2020-2023 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Mfg Campaign: 19A
Recall Date: Feb 23, 2023
Chrysler (fca Us, Llc)
Safety Issue:
Chrysler (FCA US, LLC) is recalling certain 2020-2022 Jeep Wrangler, Ram 1500, and 2021-2022 Jeep Gladiator vehicles equipped with 3.0L diesel engines. The high pressure fuel pump (HPFP) may fail, causing an engine stall.
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Mfg Campaign: Z96
Recall Date: Oct 13, 2022
Chrysler (fca Us, Llc)
Safety Issue:
Chrysler (FCA US, LLC) is recalling certain 2020-2021 Jeep Wrangler, RAM 1500 and 2021 Jeep Gladiator vehicles. A radio software error may prevent the rearview image from displaying. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Mfg Campaign: Z86
Recall Date: Aug 25, 2022
Chrysler (fca Us, Llc)
Safety Issue:
Chrysler (FCA US, LLC) is recalling certain 2018-2021 Jeep Wrangler and 2020-2021 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Mfg Campaign: Y01
Recall Date: Jan 28, 2021
Consumer Complaints
385 ComplaintsChrysler (fca Us, Llc)
Defect Description:
ENGINE
Potential Consequences:
The vehicle auto stops when putting on the driver’s seat belt, in direct conflict with owner’s manual. The owner’s manual specifies that if the “Driver’s seat belt is not buckled” it will prevent an auto stop, but preventing the auto stop is the opposite of the act of buckling the seat belt initiating the auto stop. Furthermore, the instrument cluster does not present a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents factually incorrect information to the driver and the vehicle unexpectedly stops creating driver confusion and distraction. Additionally, this creates a serious safety hazard as the issue inhibits the driver from attempting to flee an emergency situation, wherein the driver hops into an idling vehicle, plugs in their seat belt, and the vehicle turns itself off. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when putting on the driver’s seat belt, in direct conflict with owner’s manual. The owner’s manual specifies that if the “Driver’s seat belt is not buckled” it will prevent an auto stop, but preventing the auto stop is the opposite of the act of buckling the seat belt initiating the auto stop. Furthermore, the instrument cluster does not present a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents factually incorrect information to the driver and the vehicle unexpectedly stops creating driver confusion and distraction. Additionally, this creates a serious safety hazard as the issue inhibits the driver from attempting to flee an emergency situation, wherein the driver hops into an idling vehicle, plugs in their seat belt, and the vehicle turns itself off. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when putting on the driver’s seat belt, in direct conflict with owner’s manual. The owner’s manual specifies that if the “Driver’s seat belt is not buckled” it will prevent an auto stop, but preventing the auto stop is the opposite of the act of buckling the seat belt initiating the auto stop. Furthermore, the instrument cluster does not present a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents factually incorrect information to the driver and the vehicle unexpectedly stops creating driver confusion and distraction. Additionally, this creates a serious safety hazard as the issue inhibits the driver from attempting to flee an emergency situation, wherein the driver hops into an idling vehicle, plugs in their seat belt, and the vehicle turns itself off. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447513
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
ELECTRICAL SYSTEM
Potential Consequences:
The vehicle auto stops when putting on the driver’s seat belt, in direct conflict with owner’s manual. The owner’s manual specifies that if the “Driver’s seat belt is not buckled” it will prevent an auto stop, but preventing the auto stop is the opposite of the act of buckling the seat belt initiating the auto stop. Furthermore, the instrument cluster does not present a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents factually incorrect information to the driver and the vehicle unexpectedly stops creating driver confusion and distraction. Additionally, this creates a serious safety hazard as the issue inhibits the driver from attempting to flee an emergency situation, wherein the driver hops into an idling vehicle, plugs in their seat belt, and the vehicle turns itself off. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when putting on the driver’s seat belt, in direct conflict with owner’s manual. The owner’s manual specifies that if the “Driver’s seat belt is not buckled” it will prevent an auto stop, but preventing the auto stop is the opposite of the act of buckling the seat belt initiating the auto stop. Furthermore, the instrument cluster does not present a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents factually incorrect information to the driver and the vehicle unexpectedly stops creating driver confusion and distraction. Additionally, this creates a serious safety hazard as the issue inhibits the driver from attempting to flee an emergency situation, wherein the driver hops into an idling vehicle, plugs in their seat belt, and the vehicle turns itself off. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when putting on the driver’s seat belt, in direct conflict with owner’s manual. The owner’s manual specifies that if the “Driver’s seat belt is not buckled” it will prevent an auto stop, but preventing the auto stop is the opposite of the act of buckling the seat belt initiating the auto stop. Furthermore, the instrument cluster does not present a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents factually incorrect information to the driver and the vehicle unexpectedly stops creating driver confusion and distraction. Additionally, this creates a serious safety hazard as the issue inhibits the driver from attempting to flee an emergency situation, wherein the driver hops into an idling vehicle, plugs in their seat belt, and the vehicle turns itself off. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447513
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
SEAT BELTS
Potential Consequences:
The vehicle auto stops when putting on the driver’s seat belt, in direct conflict with owner’s manual. The owner’s manual specifies that if the “Driver’s seat belt is not buckled” it will prevent an auto stop, but preventing the auto stop is the opposite of the act of buckling the seat belt initiating the auto stop. Furthermore, the instrument cluster does not present a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents factually incorrect information to the driver and the vehicle unexpectedly stops creating driver confusion and distraction. Additionally, this creates a serious safety hazard as the issue inhibits the driver from attempting to flee an emergency situation, wherein the driver hops into an idling vehicle, plugs in their seat belt, and the vehicle turns itself off. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when putting on the driver’s seat belt, in direct conflict with owner’s manual. The owner’s manual specifies that if the “Driver’s seat belt is not buckled” it will prevent an auto stop, but preventing the auto stop is the opposite of the act of buckling the seat belt initiating the auto stop. Furthermore, the instrument cluster does not present a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents factually incorrect information to the driver and the vehicle unexpectedly stops creating driver confusion and distraction. Additionally, this creates a serious safety hazard as the issue inhibits the driver from attempting to flee an emergency situation, wherein the driver hops into an idling vehicle, plugs in their seat belt, and the vehicle turns itself off. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when putting on the driver’s seat belt, in direct conflict with owner’s manual. The owner’s manual specifies that if the “Driver’s seat belt is not buckled” it will prevent an auto stop, but preventing the auto stop is the opposite of the act of buckling the seat belt initiating the auto stop. Furthermore, the instrument cluster does not present a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents factually incorrect information to the driver and the vehicle unexpectedly stops creating driver confusion and distraction. Additionally, this creates a serious safety hazard as the issue inhibits the driver from attempting to flee an emergency situation, wherein the driver hops into an idling vehicle, plugs in their seat belt, and the vehicle turns itself off. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447513
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
ENGINE
Potential Consequences:
The vehicle auto stops when turning down or turning off the climate controls, in direct conflict with owner’s manual. This condition is not listed as one of the three conditions to activate an auto stop in the owner’s manual. This condition is also not listed as one of the conditions that will inhibit the vehicle from an auto stop in the owner’s manual. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when turning down or turning off the climate controls, in direct conflict with owner’s manual. This condition is not listed as one of the three conditions to activate an auto stop in the owner’s manual. This condition is also not listed as one of the conditions that will inhibit the vehicle from an auto stop in the owner’s manual. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when turning down or turning off the climate controls, in direct conflict with owner’s manual. This condition is not listed as one of the three conditions to activate an auto stop in the owner’s manual. This condition is also not listed as one of the conditions that will inhibit the vehicle from an auto stop in the owner’s manual. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447518
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
ELECTRICAL SYSTEM
Potential Consequences:
The vehicle auto stops when turning down or turning off the climate controls, in direct conflict with owner’s manual. This condition is not listed as one of the three conditions to activate an auto stop in the owner’s manual. This condition is also not listed as one of the conditions that will inhibit the vehicle from an auto stop in the owner’s manual. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when turning down or turning off the climate controls, in direct conflict with owner’s manual. This condition is not listed as one of the three conditions to activate an auto stop in the owner’s manual. This condition is also not listed as one of the conditions that will inhibit the vehicle from an auto stop in the owner’s manual. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when turning down or turning off the climate controls, in direct conflict with owner’s manual. This condition is not listed as one of the three conditions to activate an auto stop in the owner’s manual. This condition is also not listed as one of the conditions that will inhibit the vehicle from an auto stop in the owner’s manual. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447518
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
ENGINE
Potential Consequences:
The vehicle auto stops when the hood is closed and the driver remains in the seat with the seat belt buckled. The owner’s manual specifies that an open hood will prevent an auto stop, but preventing the auto stop is the opposite of closing the hood initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops which confuses and distracts the driver. Additionally, after jump starting another vehicle, the vehicle’s battery may be sufficiently depleted. Upon closing the hood, the vehicle could auto stop, and with the numerous other malfunctions impacting the auto stop system the vehicle may not be able to restart possibly leaving the driver stranded. The unexpected / wanted auto stop could cause a rear-end collision of the stranded vehicle leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when the hood is closed and the driver remains in the seat with the seat belt buckled. The owner’s manual specifies that an open hood will prevent an auto stop, but preventing the auto stop is the opposite of closing the hood initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops which confuses and distracts the driver. Additionally, after jump starting another vehicle, the vehicle’s battery may be sufficiently depleted. Upon closing the hood, the vehicle could auto stop, and with the numerous other malfunctions impacting the auto stop system the vehicle may not be able to restart possibly leaving the driver stranded. The unexpected / wanted auto stop could cause a rear-end collision of the stranded vehicle leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when the hood is closed and the driver remains in the seat with the seat belt buckled. The owner’s manual specifies that an open hood will prevent an auto stop, but preventing the auto stop is the opposite of closing the hood initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops which confuses and distracts the driver. Additionally, after jump starting another vehicle, the vehicle’s battery may be sufficiently depleted. Upon closing the hood, the vehicle could auto stop, and with the numerous other malfunctions impacting the auto stop system the vehicle may not be able to restart possibly leaving the driver stranded. The unexpected / wanted auto stop could cause a rear-end collision of the stranded vehicle leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447522
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
FUEL/PROPULSION SYSTEM
Potential Consequences:
The vehicle auto stops when the hood is closed and the driver remains in the seat with the seat belt buckled. The owner’s manual specifies that an open hood will prevent an auto stop, but preventing the auto stop is the opposite of closing the hood initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops which confuses and distracts the driver. Additionally, after jump starting another vehicle, the vehicle’s battery may be sufficiently depleted. Upon closing the hood, the vehicle could auto stop, and with the numerous other malfunctions impacting the auto stop system the vehicle may not be able to restart possibly leaving the driver stranded. The unexpected / wanted auto stop could cause a rear-end collision of the stranded vehicle leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when the hood is closed and the driver remains in the seat with the seat belt buckled. The owner’s manual specifies that an open hood will prevent an auto stop, but preventing the auto stop is the opposite of closing the hood initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops which confuses and distracts the driver. Additionally, after jump starting another vehicle, the vehicle’s battery may be sufficiently depleted. Upon closing the hood, the vehicle could auto stop, and with the numerous other malfunctions impacting the auto stop system the vehicle may not be able to restart possibly leaving the driver stranded. The unexpected / wanted auto stop could cause a rear-end collision of the stranded vehicle leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when the hood is closed and the driver remains in the seat with the seat belt buckled. The owner’s manual specifies that an open hood will prevent an auto stop, but preventing the auto stop is the opposite of closing the hood initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops which confuses and distracts the driver. Additionally, after jump starting another vehicle, the vehicle’s battery may be sufficiently depleted. Upon closing the hood, the vehicle could auto stop, and with the numerous other malfunctions impacting the auto stop system the vehicle may not be able to restart possibly leaving the driver stranded. The unexpected / wanted auto stop could cause a rear-end collision of the stranded vehicle leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447522
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
ELECTRICAL SYSTEM
Potential Consequences:
The vehicle auto stops when the hood is closed and the driver remains in the seat with the seat belt buckled. The owner’s manual specifies that an open hood will prevent an auto stop, but preventing the auto stop is the opposite of closing the hood initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops which confuses and distracts the driver. Additionally, after jump starting another vehicle, the vehicle’s battery may be sufficiently depleted. Upon closing the hood, the vehicle could auto stop, and with the numerous other malfunctions impacting the auto stop system the vehicle may not be able to restart possibly leaving the driver stranded. The unexpected / wanted auto stop could cause a rear-end collision of the stranded vehicle leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when the hood is closed and the driver remains in the seat with the seat belt buckled. The owner’s manual specifies that an open hood will prevent an auto stop, but preventing the auto stop is the opposite of closing the hood initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops which confuses and distracts the driver. Additionally, after jump starting another vehicle, the vehicle’s battery may be sufficiently depleted. Upon closing the hood, the vehicle could auto stop, and with the numerous other malfunctions impacting the auto stop system the vehicle may not be able to restart possibly leaving the driver stranded. The unexpected / wanted auto stop could cause a rear-end collision of the stranded vehicle leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when the hood is closed and the driver remains in the seat with the seat belt buckled. The owner’s manual specifies that an open hood will prevent an auto stop, but preventing the auto stop is the opposite of closing the hood initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops which confuses and distracts the driver. Additionally, after jump starting another vehicle, the vehicle’s battery may be sufficiently depleted. Upon closing the hood, the vehicle could auto stop, and with the numerous other malfunctions impacting the auto stop system the vehicle may not be able to restart possibly leaving the driver stranded. The unexpected / wanted auto stop could cause a rear-end collision of the stranded vehicle leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447522
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
ELECTRICAL SYSTEM
Potential Consequences:
The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. The vehicle fails to properly check for the empty driver’s seat safety condition before auto stop. This auto stop violates Jeep’s published safety check condition and poses a serious safety hazard. This issue poses additionally serious safety hazards as the vehicle will shut off with the driver outside the vehicle, leaving the driver with an incorrect understanding that the vehicle is properly locked out from an auto start condition. Therefore, if the driver is operating on or under the vehicle with it auto stopped, the passenger can unintendedly auto start the vehicle resulting in a serious injury or the loss of a finger. Additionally, in thinking that the vehicle is off the driver may leave the vehicle unattended in their garage and after 5 minutes the vehicle will auto start filling the garage / house with toxic fumes and presenting a serious life-threatening fire hazard. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. The vehicle fails to properly check for the empty driver’s seat safety condition before auto stop. This auto stop violates Jeep’s published safety check condition and poses a serious safety hazard. This issue poses additionally serious safety hazards as the vehicle will shut off with the driver outside the vehicle, leaving the driver with an incorrect understanding that the vehicle is properly locked out from an auto start condition. Therefore, if the driver is operating on or under the vehicle with it auto stopped, the passenger can unintendedly auto start the vehicle resulting in a serious injury or the loss of a finger. Additionally, in thinking that the vehicle is off the driver may leave the vehicle unattended in their garage and after 5 minutes the vehicle will auto start filling the garage / house with toxic fumes and presenting a serious life-threatening fire hazard. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. The vehicle fails to properly check for the empty driver’s seat safety condition before auto stop. This auto stop violates Jeep’s published safety check condition and poses a serious safety hazard. This issue poses additionally serious safety hazards as the vehicle will shut off with the driver outside the vehicle, leaving the driver with an incorrect understanding that the vehicle is properly locked out from an auto start condition. Therefore, if the driver is operating on or under the vehicle with it auto stopped, the passenger can unintendedly auto start the vehicle resulting in a serious injury or the loss of a finger. Additionally, in thinking that the vehicle is off the driver may leave the vehicle unattended in their garage and after 5 minutes the vehicle will auto start filling the garage / house with toxic fumes and presenting a serious life-threatening fire hazard. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447525
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
ENGINE
Potential Consequences:
The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. The vehicle fails to properly check for the empty driver’s seat safety condition before auto stop. This auto stop violates Jeep’s published safety check condition and poses a serious safety hazard. This issue poses additionally serious safety hazards as the vehicle will shut off with the driver outside the vehicle, leaving the driver with an incorrect understanding that the vehicle is properly locked out from an auto start condition. Therefore, if the driver is operating on or under the vehicle with it auto stopped, the passenger can unintendedly auto start the vehicle resulting in a serious injury or the loss of a finger. Additionally, in thinking that the vehicle is off the driver may leave the vehicle unattended in their garage and after 5 minutes the vehicle will auto start filling the garage / house with toxic fumes and presenting a serious life-threatening fire hazard. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. The vehicle fails to properly check for the empty driver’s seat safety condition before auto stop. This auto stop violates Jeep’s published safety check condition and poses a serious safety hazard. This issue poses additionally serious safety hazards as the vehicle will shut off with the driver outside the vehicle, leaving the driver with an incorrect understanding that the vehicle is properly locked out from an auto start condition. Therefore, if the driver is operating on or under the vehicle with it auto stopped, the passenger can unintendedly auto start the vehicle resulting in a serious injury or the loss of a finger. Additionally, in thinking that the vehicle is off the driver may leave the vehicle unattended in their garage and after 5 minutes the vehicle will auto start filling the garage / house with toxic fumes and presenting a serious life-threatening fire hazard. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. The vehicle fails to properly check for the empty driver’s seat safety condition before auto stop. This auto stop violates Jeep’s published safety check condition and poses a serious safety hazard. This issue poses additionally serious safety hazards as the vehicle will shut off with the driver outside the vehicle, leaving the driver with an incorrect understanding that the vehicle is properly locked out from an auto start condition. Therefore, if the driver is operating on or under the vehicle with it auto stopped, the passenger can unintendedly auto start the vehicle resulting in a serious injury or the loss of a finger. Additionally, in thinking that the vehicle is off the driver may leave the vehicle unattended in their garage and after 5 minutes the vehicle will auto start filling the garage / house with toxic fumes and presenting a serious life-threatening fire hazard. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447525
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
SEATS
Potential Consequences:
The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. The vehicle fails to properly check for the empty driver’s seat safety condition before auto stop. This auto stop violates Jeep’s published safety check condition and poses a serious safety hazard. This issue poses additionally serious safety hazards as the vehicle will shut off with the driver outside the vehicle, leaving the driver with an incorrect understanding that the vehicle is properly locked out from an auto start condition. Therefore, if the driver is operating on or under the vehicle with it auto stopped, the passenger can unintendedly auto start the vehicle resulting in a serious injury or the loss of a finger. Additionally, in thinking that the vehicle is off the driver may leave the vehicle unattended in their garage and after 5 minutes the vehicle will auto start filling the garage / house with toxic fumes and presenting a serious life-threatening fire hazard. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. The vehicle fails to properly check for the empty driver’s seat safety condition before auto stop. This auto stop violates Jeep’s published safety check condition and poses a serious safety hazard. This issue poses additionally serious safety hazards as the vehicle will shut off with the driver outside the vehicle, leaving the driver with an incorrect understanding that the vehicle is properly locked out from an auto start condition. Therefore, if the driver is operating on or under the vehicle with it auto stopped, the passenger can unintendedly auto start the vehicle resulting in a serious injury or the loss of a finger. Additionally, in thinking that the vehicle is off the driver may leave the vehicle unattended in their garage and after 5 minutes the vehicle will auto start filling the garage / house with toxic fumes and presenting a serious life-threatening fire hazard. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. The vehicle fails to properly check for the empty driver’s seat safety condition before auto stop. This auto stop violates Jeep’s published safety check condition and poses a serious safety hazard. This issue poses additionally serious safety hazards as the vehicle will shut off with the driver outside the vehicle, leaving the driver with an incorrect understanding that the vehicle is properly locked out from an auto start condition. Therefore, if the driver is operating on or under the vehicle with it auto stopped, the passenger can unintendedly auto start the vehicle resulting in a serious injury or the loss of a finger. Additionally, in thinking that the vehicle is off the driver may leave the vehicle unattended in their garage and after 5 minutes the vehicle will auto start filling the garage / house with toxic fumes and presenting a serious life-threatening fire hazard. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447525
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
ELECTRICAL SYSTEM
Potential Consequences:
The failure of the vehicle’s safety condition check for an empty driver’s seat for an auto stop indicates that the “Occupant Restraint Controller (ORC)” and/or the “Advanced Front Air Bag system” are not receiving proper information. This creates a serious safety hazard as the front air bags may not deploy or may not “adjust the inflation rate of the Advanced Front Air Bags” as specified in the owner’s manual. For driver safety, these systems and their associated sensors should be fully examined and tested. The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. The vehicle fails to properly check for the empty driver’s seat safety condition before initiating an auto stop. The associated auto stop malfunction was reproduced and confirmed by multiple service personnel at 2 Jeep dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“, despite the vehicle operating in violation of the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The failure of the vehicle’s safety condition check for an empty driver’s seat for an auto stop indicates that the “Occupant Restraint Controller (ORC)” and/or the “Advanced Front Air Bag system” are not receiving proper information. This creates a serious safety hazard as the front air bags may not deploy or may not “adjust the inflation rate of the Advanced Front Air Bags” as specified in the owner’s manual. For driver safety, these systems and their associated sensors should be fully examined and tested. The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. The vehicle fails to properly check for the empty driver’s seat safety condition before initiating an auto stop. The associated auto stop malfunction was reproduced and confirmed by multiple service personnel at 2 Jeep dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“, despite the vehicle operating in violation of the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The failure of the vehicle’s safety condition check for an empty driver’s seat for an auto stop indicates that the “Occupant Restraint Controller (ORC)” and/or the “Advanced Front Air Bag system” are not receiving proper information. This creates a serious safety hazard as the front air bags may not deploy or may not “adjust the inflation rate of the Advanced Front Air Bags” as specified in the owner’s manual. For driver safety, these systems and their associated sensors should be fully examined and tested. The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. The vehicle fails to properly check for the empty driver’s seat safety condition before initiating an auto stop. The associated auto stop malfunction was reproduced and confirmed by multiple service personnel at 2 Jeep dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“, despite the vehicle operating in violation of the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447530
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
ENGINE
Potential Consequences:
The failure of the vehicle’s safety condition check for an empty driver’s seat for an auto stop indicates that the “Occupant Restraint Controller (ORC)” and/or the “Advanced Front Air Bag system” are not receiving proper information. This creates a serious safety hazard as the front air bags may not deploy or may not “adjust the inflation rate of the Advanced Front Air Bags” as specified in the owner’s manual. For driver safety, these systems and their associated sensors should be fully examined and tested. The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. The vehicle fails to properly check for the empty driver’s seat safety condition before initiating an auto stop. The associated auto stop malfunction was reproduced and confirmed by multiple service personnel at 2 Jeep dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“, despite the vehicle operating in violation of the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The failure of the vehicle’s safety condition check for an empty driver’s seat for an auto stop indicates that the “Occupant Restraint Controller (ORC)” and/or the “Advanced Front Air Bag system” are not receiving proper information. This creates a serious safety hazard as the front air bags may not deploy or may not “adjust the inflation rate of the Advanced Front Air Bags” as specified in the owner’s manual. For driver safety, these systems and their associated sensors should be fully examined and tested. The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. The vehicle fails to properly check for the empty driver’s seat safety condition before initiating an auto stop. The associated auto stop malfunction was reproduced and confirmed by multiple service personnel at 2 Jeep dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“, despite the vehicle operating in violation of the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The failure of the vehicle’s safety condition check for an empty driver’s seat for an auto stop indicates that the “Occupant Restraint Controller (ORC)” and/or the “Advanced Front Air Bag system” are not receiving proper information. This creates a serious safety hazard as the front air bags may not deploy or may not “adjust the inflation rate of the Advanced Front Air Bags” as specified in the owner’s manual. For driver safety, these systems and their associated sensors should be fully examined and tested. The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. The vehicle fails to properly check for the empty driver’s seat safety condition before initiating an auto stop. The associated auto stop malfunction was reproduced and confirmed by multiple service personnel at 2 Jeep dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“, despite the vehicle operating in violation of the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447530
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
AIR BAGS
Potential Consequences:
The failure of the vehicle’s safety condition check for an empty driver’s seat for an auto stop indicates that the “Occupant Restraint Controller (ORC)” and/or the “Advanced Front Air Bag system” are not receiving proper information. This creates a serious safety hazard as the front air bags may not deploy or may not “adjust the inflation rate of the Advanced Front Air Bags” as specified in the owner’s manual. For driver safety, these systems and their associated sensors should be fully examined and tested. The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. The vehicle fails to properly check for the empty driver’s seat safety condition before initiating an auto stop. The associated auto stop malfunction was reproduced and confirmed by multiple service personnel at 2 Jeep dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“, despite the vehicle operating in violation of the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The failure of the vehicle’s safety condition check for an empty driver’s seat for an auto stop indicates that the “Occupant Restraint Controller (ORC)” and/or the “Advanced Front Air Bag system” are not receiving proper information. This creates a serious safety hazard as the front air bags may not deploy or may not “adjust the inflation rate of the Advanced Front Air Bags” as specified in the owner’s manual. For driver safety, these systems and their associated sensors should be fully examined and tested. The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. The vehicle fails to properly check for the empty driver’s seat safety condition before initiating an auto stop. The associated auto stop malfunction was reproduced and confirmed by multiple service personnel at 2 Jeep dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“, despite the vehicle operating in violation of the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The failure of the vehicle’s safety condition check for an empty driver’s seat for an auto stop indicates that the “Occupant Restraint Controller (ORC)” and/or the “Advanced Front Air Bag system” are not receiving proper information. This creates a serious safety hazard as the front air bags may not deploy or may not “adjust the inflation rate of the Advanced Front Air Bags” as specified in the owner’s manual. For driver safety, these systems and their associated sensors should be fully examined and tested. The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. The vehicle fails to properly check for the empty driver’s seat safety condition before initiating an auto stop. The associated auto stop malfunction was reproduced and confirmed by multiple service personnel at 2 Jeep dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“, despite the vehicle operating in violation of the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447530
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
ENGINE
Potential Consequences:
The vehicle auto stops when the steering wheel is turned, in direct conflict with owner’s manual. The owner’s manual specifies that “Steering angle beyond threshold” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when the steering wheel is turned, in direct conflict with owner’s manual. The owner’s manual specifies that “Steering angle beyond threshold” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when the steering wheel is turned, in direct conflict with owner’s manual. The owner’s manual specifies that “Steering angle beyond threshold” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447531
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
FUEL/PROPULSION SYSTEM
Potential Consequences:
The vehicle auto stops when the steering wheel is turned, in direct conflict with owner’s manual. The owner’s manual specifies that “Steering angle beyond threshold” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when the steering wheel is turned, in direct conflict with owner’s manual. The owner’s manual specifies that “Steering angle beyond threshold” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when the steering wheel is turned, in direct conflict with owner’s manual. The owner’s manual specifies that “Steering angle beyond threshold” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447531
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
STEERING
Potential Consequences:
The vehicle auto stops when the steering wheel is turned, in direct conflict with owner’s manual. The owner’s manual specifies that “Steering angle beyond threshold” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when the steering wheel is turned, in direct conflict with owner’s manual. The owner’s manual specifies that “Steering angle beyond threshold” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when the steering wheel is turned, in direct conflict with owner’s manual. The owner’s manual specifies that “Steering angle beyond threshold” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447531
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
ENGINE
Potential Consequences:
The vehicle auto stops when the defrost is turned off, in direct conflict with owner’s manual. The owner’s manual specifies that “HVAC is set to full defrost mode” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Additionally, this issue occurs when the HVAC is operating at less than full defrost mode. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when the defrost is turned off, in direct conflict with owner’s manual. The owner’s manual specifies that “HVAC is set to full defrost mode” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Additionally, this issue occurs when the HVAC is operating at less than full defrost mode. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when the defrost is turned off, in direct conflict with owner’s manual. The owner’s manual specifies that “HVAC is set to full defrost mode” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Additionally, this issue occurs when the HVAC is operating at less than full defrost mode. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447532
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
FUEL/PROPULSION SYSTEM
Potential Consequences:
The vehicle auto stops when the defrost is turned off, in direct conflict with owner’s manual. The owner’s manual specifies that “HVAC is set to full defrost mode” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Additionally, this issue occurs when the HVAC is operating at less than full defrost mode. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto stops when the defrost is turned off, in direct conflict with owner’s manual. The owner’s manual specifies that “HVAC is set to full defrost mode” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Additionally, this issue occurs when the HVAC is operating at less than full defrost mode. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto stops when the defrost is turned off, in direct conflict with owner’s manual. The owner’s manual specifies that “HVAC is set to full defrost mode” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Additionally, this issue occurs when the HVAC is operating at less than full defrost mode. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447532
Recall Date: Jan 14, 2022
Chrysler (fca Us, Llc)
Defect Description:
ELECTRICAL SYSTEM
Potential Consequences:
The vehicle auto starts when opening the driver’s door. This is not listed under “Conditions that will cause the engine to start automatically while in STOP/START AUTO STOP ACTIVE mode” in the owner’s manual. Other Jeep models do not auto start upon opening the driver’s door. This auto start issue poses a serious safety hazard as the vehicle will unexpectedly start and begin to roll when the driver’s door is open and the driver is not properly secure in the driver seat. The unexpected / wanted start could cause a collision with another vehicle or pedestrian leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel at 2 Jeep dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Corrective Action:
The vehicle auto starts when opening the driver’s door. This is not listed under “Conditions that will cause the engine to start automatically while in STOP/START AUTO STOP ACTIVE mode” in the owner’s manual. Other Jeep models do not auto start upon opening the driver’s door. This auto start issue poses a serious safety hazard as the vehicle will unexpectedly start and begin to roll when the driver’s door is open and the driver is not properly secure in the driver seat. The unexpected / wanted start could cause a collision with another vehicle or pedestrian leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel at 2 Jeep dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Additional Notes:
The vehicle auto starts when opening the driver’s door. This is not listed under “Conditions that will cause the engine to start automatically while in STOP/START AUTO STOP ACTIVE mode” in the owner’s manual. Other Jeep models do not auto start upon opening the driver’s door. This auto start issue poses a serious safety hazard as the vehicle will unexpectedly start and begin to roll when the driver’s door is open and the driver is not properly secure in the driver seat. The unexpected / wanted start could cause a collision with another vehicle or pedestrian leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel at 2 Jeep dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“. This portion of the vehicle’s Auto Start / Stop System is NOT operating as designed and documented in the owner’s manual. I feel unsafe driving the vehicle, as this is one of numerous hardware / software malfunctions plaguing the vehicle. The vehicle is available for inspection upon request.
Mfg Campaign: 11447533
Recall Date: Jan 14, 2022
Need Legal Help?
Featured Attorneys
Barry Edzant
Edzant Price LLC
Valencia, CA • 36 yrs
Focus: Lemon Law, Personal Injury
Recent Articles
Jeep Grand Cherokee Head Restraint Problem
Chrysler (FCA US, LLC) has announced a safety issue affecting certain 2023–2024 Jeep Grand Ch ...
Aug 1, 2025Fuel Injector Problem: 2021-2024 Ford Bronco Sport and 2020-2022 Ford Escape
If you own a 2021-2024 Ford Bronco Sport or 2020-2022 Ford Escape equipped with a 1.5L Dragon GTDI e ...
Jul 28, 2025Airbag Problem Affects 2022-2025 Chrysler Pacifica and Voyager Vehicles
If you own a Chrysler Pacifica or Voyager, your vehicle may be equipped with defective side curtain ...
Jul 24, 2025