Complaints & Recalls
Official Safety Recalls - Important!
7 RecallsThese are official manufacturer recalls ordered by NHTSA for safety defects. If you own this vehicle, contact your dealer immediately for free repairs.
Daimler Trucks North America, Llc
Safety Issue:
Daimler Trucks North America, LLC (DTNA) is recalling certain 2024 FCCC MT45G, MT45, and Freightliner Cascadia vehicles. The steering gear assemblies may have been assembled incorrectly with fewer recirculating balls than are required, which may result in a loss of steering control.
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Mfg Campaign: FL995
Recall Date: Feb 8, 2024
Daimler Trucks North America, Llc
Safety Issue:
Daimler Trucks North America, LLC (DTNA) is recalling certain short wheelbase 2020-2024 Freightliner Cascadia, 2021-2024 Freightliner M2 Business Class, 2022 Western Star 4700, and 2020 Freightliner Classic Cascadia vehicles. The vehicle is equipped with an electronic stability control system and tire combination that may understeer during a J-turn. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 136, "Electronic Stability Control Systems on Heavy Vehicles."
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Mfg Campaign: FL971
Recall Date: Apr 26, 2023
Consumer Complaints
26 ComplaintsDaimler Trucks North America, Llc
Defect Description:
TIRES
Potential Consequences:
See attached document for complaint.
Corrective Action:
See attached document for complaint.
Additional Notes:
See attached document for complaint.
Mfg Campaign: 11668076
Recall Date: Jun 20, 2025
Daimler Trucks North America, Llc
Defect Description:
FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
Potential Consequences:
The cruise control (level 2 autonomous) will turn itself off without any warning sometimes. This happens any time the truck is set for above the speed limit by more than 2 mph. The truck uses a speed limit map, independent of actual posted speed limits. When the truck detects a speed limit drop to below the cruise setting, either real or imagined, the cruise control disengages without any warning or notification. This is a problem when I expect the truck to continue its autonomous function in traffic situations, but it does not, and without warning. The system will even disengage while it is operating; it will be slowing or maintaining a following distance, then disengage. The driver has no idea if the truck is still auto-driving until he is close to a rear-end accident. Also, bear in mind that speed limit signs are often only posted on the right side of the road; If there is something blocking the sign, like another vehicle, the cruise will still disengage without warning, and the driver does not know it. The only way to tell if cruise is still engaged is by looking for a small green icon in the bottom left of the dash display, which is over 20 degrees down from focal view. Also, there are times when the cruise disengages for no apparent reason. Sometimes there is a barely audible bluetooth-disconnect type sound, but often there is no audible warning. There is also no display warning of any type.
Corrective Action:
The cruise control (level 2 autonomous) will turn itself off without any warning sometimes. This happens any time the truck is set for above the speed limit by more than 2 mph. The truck uses a speed limit map, independent of actual posted speed limits. When the truck detects a speed limit drop to below the cruise setting, either real or imagined, the cruise control disengages without any warning or notification. This is a problem when I expect the truck to continue its autonomous function in traffic situations, but it does not, and without warning. The system will even disengage while it is operating; it will be slowing or maintaining a following distance, then disengage. The driver has no idea if the truck is still auto-driving until he is close to a rear-end accident. Also, bear in mind that speed limit signs are often only posted on the right side of the road; If there is something blocking the sign, like another vehicle, the cruise will still disengage without warning, and the driver does not know it. The only way to tell if cruise is still engaged is by looking for a small green icon in the bottom left of the dash display, which is over 20 degrees down from focal view. Also, there are times when the cruise disengages for no apparent reason. Sometimes there is a barely audible bluetooth-disconnect type sound, but often there is no audible warning. There is also no display warning of any type.
Additional Notes:
The cruise control (level 2 autonomous) will turn itself off without any warning sometimes. This happens any time the truck is set for above the speed limit by more than 2 mph. The truck uses a speed limit map, independent of actual posted speed limits. When the truck detects a speed limit drop to below the cruise setting, either real or imagined, the cruise control disengages without any warning or notification. This is a problem when I expect the truck to continue its autonomous function in traffic situations, but it does not, and without warning. The system will even disengage while it is operating; it will be slowing or maintaining a following distance, then disengage. The driver has no idea if the truck is still auto-driving until he is close to a rear-end accident. Also, bear in mind that speed limit signs are often only posted on the right side of the road; If there is something blocking the sign, like another vehicle, the cruise will still disengage without warning, and the driver does not know it. The only way to tell if cruise is still engaged is by looking for a small green icon in the bottom left of the dash display, which is over 20 degrees down from focal view. Also, there are times when the cruise disengages for no apparent reason. Sometimes there is a barely audible bluetooth-disconnect type sound, but often there is no audible warning. There is also no display warning of any type.
Mfg Campaign: 11633126
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
FORWARD COLLISION AVOIDANCE: WARNINGS
Potential Consequences:
The cruise control (level 2 autonomous) will turn itself off without any warning sometimes. This happens any time the truck is set for above the speed limit by more than 2 mph. The truck uses a speed limit map, independent of actual posted speed limits. When the truck detects a speed limit drop to below the cruise setting, either real or imagined, the cruise control disengages without any warning or notification. This is a problem when I expect the truck to continue its autonomous function in traffic situations, but it does not, and without warning. The system will even disengage while it is operating; it will be slowing or maintaining a following distance, then disengage. The driver has no idea if the truck is still auto-driving until he is close to a rear-end accident. Also, bear in mind that speed limit signs are often only posted on the right side of the road; If there is something blocking the sign, like another vehicle, the cruise will still disengage without warning, and the driver does not know it. The only way to tell if cruise is still engaged is by looking for a small green icon in the bottom left of the dash display, which is over 20 degrees down from focal view. Also, there are times when the cruise disengages for no apparent reason. Sometimes there is a barely audible bluetooth-disconnect type sound, but often there is no audible warning. There is also no display warning of any type.
Corrective Action:
The cruise control (level 2 autonomous) will turn itself off without any warning sometimes. This happens any time the truck is set for above the speed limit by more than 2 mph. The truck uses a speed limit map, independent of actual posted speed limits. When the truck detects a speed limit drop to below the cruise setting, either real or imagined, the cruise control disengages without any warning or notification. This is a problem when I expect the truck to continue its autonomous function in traffic situations, but it does not, and without warning. The system will even disengage while it is operating; it will be slowing or maintaining a following distance, then disengage. The driver has no idea if the truck is still auto-driving until he is close to a rear-end accident. Also, bear in mind that speed limit signs are often only posted on the right side of the road; If there is something blocking the sign, like another vehicle, the cruise will still disengage without warning, and the driver does not know it. The only way to tell if cruise is still engaged is by looking for a small green icon in the bottom left of the dash display, which is over 20 degrees down from focal view. Also, there are times when the cruise disengages for no apparent reason. Sometimes there is a barely audible bluetooth-disconnect type sound, but often there is no audible warning. There is also no display warning of any type.
Additional Notes:
The cruise control (level 2 autonomous) will turn itself off without any warning sometimes. This happens any time the truck is set for above the speed limit by more than 2 mph. The truck uses a speed limit map, independent of actual posted speed limits. When the truck detects a speed limit drop to below the cruise setting, either real or imagined, the cruise control disengages without any warning or notification. This is a problem when I expect the truck to continue its autonomous function in traffic situations, but it does not, and without warning. The system will even disengage while it is operating; it will be slowing or maintaining a following distance, then disengage. The driver has no idea if the truck is still auto-driving until he is close to a rear-end accident. Also, bear in mind that speed limit signs are often only posted on the right side of the road; If there is something blocking the sign, like another vehicle, the cruise will still disengage without warning, and the driver does not know it. The only way to tell if cruise is still engaged is by looking for a small green icon in the bottom left of the dash display, which is over 20 degrees down from focal view. Also, there are times when the cruise disengages for no apparent reason. Sometimes there is a barely audible bluetooth-disconnect type sound, but often there is no audible warning. There is also no display warning of any type.
Mfg Campaign: 11633126
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
VEHICLE SPEED CONTROL
Potential Consequences:
The cruise control (level 2 autonomous) will turn itself off without any warning sometimes. This happens any time the truck is set for above the speed limit by more than 2 mph. The truck uses a speed limit map, independent of actual posted speed limits. When the truck detects a speed limit drop to below the cruise setting, either real or imagined, the cruise control disengages without any warning or notification. This is a problem when I expect the truck to continue its autonomous function in traffic situations, but it does not, and without warning. The system will even disengage while it is operating; it will be slowing or maintaining a following distance, then disengage. The driver has no idea if the truck is still auto-driving until he is close to a rear-end accident. Also, bear in mind that speed limit signs are often only posted on the right side of the road; If there is something blocking the sign, like another vehicle, the cruise will still disengage without warning, and the driver does not know it. The only way to tell if cruise is still engaged is by looking for a small green icon in the bottom left of the dash display, which is over 20 degrees down from focal view. Also, there are times when the cruise disengages for no apparent reason. Sometimes there is a barely audible bluetooth-disconnect type sound, but often there is no audible warning. There is also no display warning of any type.
Corrective Action:
The cruise control (level 2 autonomous) will turn itself off without any warning sometimes. This happens any time the truck is set for above the speed limit by more than 2 mph. The truck uses a speed limit map, independent of actual posted speed limits. When the truck detects a speed limit drop to below the cruise setting, either real or imagined, the cruise control disengages without any warning or notification. This is a problem when I expect the truck to continue its autonomous function in traffic situations, but it does not, and without warning. The system will even disengage while it is operating; it will be slowing or maintaining a following distance, then disengage. The driver has no idea if the truck is still auto-driving until he is close to a rear-end accident. Also, bear in mind that speed limit signs are often only posted on the right side of the road; If there is something blocking the sign, like another vehicle, the cruise will still disengage without warning, and the driver does not know it. The only way to tell if cruise is still engaged is by looking for a small green icon in the bottom left of the dash display, which is over 20 degrees down from focal view. Also, there are times when the cruise disengages for no apparent reason. Sometimes there is a barely audible bluetooth-disconnect type sound, but often there is no audible warning. There is also no display warning of any type.
Additional Notes:
The cruise control (level 2 autonomous) will turn itself off without any warning sometimes. This happens any time the truck is set for above the speed limit by more than 2 mph. The truck uses a speed limit map, independent of actual posted speed limits. When the truck detects a speed limit drop to below the cruise setting, either real or imagined, the cruise control disengages without any warning or notification. This is a problem when I expect the truck to continue its autonomous function in traffic situations, but it does not, and without warning. The system will even disengage while it is operating; it will be slowing or maintaining a following distance, then disengage. The driver has no idea if the truck is still auto-driving until he is close to a rear-end accident. Also, bear in mind that speed limit signs are often only posted on the right side of the road; If there is something blocking the sign, like another vehicle, the cruise will still disengage without warning, and the driver does not know it. The only way to tell if cruise is still engaged is by looking for a small green icon in the bottom left of the dash display, which is over 20 degrees down from focal view. Also, there are times when the cruise disengages for no apparent reason. Sometimes there is a barely audible bluetooth-disconnect type sound, but often there is no audible warning. There is also no display warning of any type.
Mfg Campaign: 11633126
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
Potential Consequences:
When approaching stopped traffic, sometimes the truck will respond and begin to slow down. At other times, the truck will continue at set speed toward a detected stopped vehicle, and in situations where the time and distance are way too short to justify no reaction by the system. The truck at sometimes acts like it is auto-driving; at others it acts as if it is only in crash-mitigation mode, and will wait for the driver until the last possible second and then slam on brakes. There have been some times where the truck actually gave a collision warning (alarm and display turns red), but in no way attempted to slow itself. This happens with vehicles detected in the truck's headway for multiple seconds beforehand. In short, the truck will sometimes apparently allow itself to rear-end a vehicle in front of itself, even though the sensors detected it and it had plenty of time to react. When there has been a collision warning with no action by the autonomous system, it has often been when there is less than 1/2 second for the driver to intervene.
Corrective Action:
When approaching stopped traffic, sometimes the truck will respond and begin to slow down. At other times, the truck will continue at set speed toward a detected stopped vehicle, and in situations where the time and distance are way too short to justify no reaction by the system. The truck at sometimes acts like it is auto-driving; at others it acts as if it is only in crash-mitigation mode, and will wait for the driver until the last possible second and then slam on brakes. There have been some times where the truck actually gave a collision warning (alarm and display turns red), but in no way attempted to slow itself. This happens with vehicles detected in the truck's headway for multiple seconds beforehand. In short, the truck will sometimes apparently allow itself to rear-end a vehicle in front of itself, even though the sensors detected it and it had plenty of time to react. When there has been a collision warning with no action by the autonomous system, it has often been when there is less than 1/2 second for the driver to intervene.
Additional Notes:
When approaching stopped traffic, sometimes the truck will respond and begin to slow down. At other times, the truck will continue at set speed toward a detected stopped vehicle, and in situations where the time and distance are way too short to justify no reaction by the system. The truck at sometimes acts like it is auto-driving; at others it acts as if it is only in crash-mitigation mode, and will wait for the driver until the last possible second and then slam on brakes. There have been some times where the truck actually gave a collision warning (alarm and display turns red), but in no way attempted to slow itself. This happens with vehicles detected in the truck's headway for multiple seconds beforehand. In short, the truck will sometimes apparently allow itself to rear-end a vehicle in front of itself, even though the sensors detected it and it had plenty of time to react. When there has been a collision warning with no action by the autonomous system, it has often been when there is less than 1/2 second for the driver to intervene.
Mfg Campaign: 11633128
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
FORWARD COLLISION AVOIDANCE: WARNINGS
Potential Consequences:
When approaching stopped traffic, sometimes the truck will respond and begin to slow down. At other times, the truck will continue at set speed toward a detected stopped vehicle, and in situations where the time and distance are way too short to justify no reaction by the system. The truck at sometimes acts like it is auto-driving; at others it acts as if it is only in crash-mitigation mode, and will wait for the driver until the last possible second and then slam on brakes. There have been some times where the truck actually gave a collision warning (alarm and display turns red), but in no way attempted to slow itself. This happens with vehicles detected in the truck's headway for multiple seconds beforehand. In short, the truck will sometimes apparently allow itself to rear-end a vehicle in front of itself, even though the sensors detected it and it had plenty of time to react. When there has been a collision warning with no action by the autonomous system, it has often been when there is less than 1/2 second for the driver to intervene.
Corrective Action:
When approaching stopped traffic, sometimes the truck will respond and begin to slow down. At other times, the truck will continue at set speed toward a detected stopped vehicle, and in situations where the time and distance are way too short to justify no reaction by the system. The truck at sometimes acts like it is auto-driving; at others it acts as if it is only in crash-mitigation mode, and will wait for the driver until the last possible second and then slam on brakes. There have been some times where the truck actually gave a collision warning (alarm and display turns red), but in no way attempted to slow itself. This happens with vehicles detected in the truck's headway for multiple seconds beforehand. In short, the truck will sometimes apparently allow itself to rear-end a vehicle in front of itself, even though the sensors detected it and it had plenty of time to react. When there has been a collision warning with no action by the autonomous system, it has often been when there is less than 1/2 second for the driver to intervene.
Additional Notes:
When approaching stopped traffic, sometimes the truck will respond and begin to slow down. At other times, the truck will continue at set speed toward a detected stopped vehicle, and in situations where the time and distance are way too short to justify no reaction by the system. The truck at sometimes acts like it is auto-driving; at others it acts as if it is only in crash-mitigation mode, and will wait for the driver until the last possible second and then slam on brakes. There have been some times where the truck actually gave a collision warning (alarm and display turns red), but in no way attempted to slow itself. This happens with vehicles detected in the truck's headway for multiple seconds beforehand. In short, the truck will sometimes apparently allow itself to rear-end a vehicle in front of itself, even though the sensors detected it and it had plenty of time to react. When there has been a collision warning with no action by the autonomous system, it has often been when there is less than 1/2 second for the driver to intervene.
Mfg Campaign: 11633128
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING
Potential Consequences:
When approaching stopped traffic, sometimes the truck will respond and begin to slow down. At other times, the truck will continue at set speed toward a detected stopped vehicle, and in situations where the time and distance are way too short to justify no reaction by the system. The truck at sometimes acts like it is auto-driving; at others it acts as if it is only in crash-mitigation mode, and will wait for the driver until the last possible second and then slam on brakes. There have been some times where the truck actually gave a collision warning (alarm and display turns red), but in no way attempted to slow itself. This happens with vehicles detected in the truck's headway for multiple seconds beforehand. In short, the truck will sometimes apparently allow itself to rear-end a vehicle in front of itself, even though the sensors detected it and it had plenty of time to react. When there has been a collision warning with no action by the autonomous system, it has often been when there is less than 1/2 second for the driver to intervene.
Corrective Action:
When approaching stopped traffic, sometimes the truck will respond and begin to slow down. At other times, the truck will continue at set speed toward a detected stopped vehicle, and in situations where the time and distance are way too short to justify no reaction by the system. The truck at sometimes acts like it is auto-driving; at others it acts as if it is only in crash-mitigation mode, and will wait for the driver until the last possible second and then slam on brakes. There have been some times where the truck actually gave a collision warning (alarm and display turns red), but in no way attempted to slow itself. This happens with vehicles detected in the truck's headway for multiple seconds beforehand. In short, the truck will sometimes apparently allow itself to rear-end a vehicle in front of itself, even though the sensors detected it and it had plenty of time to react. When there has been a collision warning with no action by the autonomous system, it has often been when there is less than 1/2 second for the driver to intervene.
Additional Notes:
When approaching stopped traffic, sometimes the truck will respond and begin to slow down. At other times, the truck will continue at set speed toward a detected stopped vehicle, and in situations where the time and distance are way too short to justify no reaction by the system. The truck at sometimes acts like it is auto-driving; at others it acts as if it is only in crash-mitigation mode, and will wait for the driver until the last possible second and then slam on brakes. There have been some times where the truck actually gave a collision warning (alarm and display turns red), but in no way attempted to slow itself. This happens with vehicles detected in the truck's headway for multiple seconds beforehand. In short, the truck will sometimes apparently allow itself to rear-end a vehicle in front of itself, even though the sensors detected it and it had plenty of time to react. When there has been a collision warning with no action by the autonomous system, it has often been when there is less than 1/2 second for the driver to intervene.
Mfg Campaign: 11633128
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
VEHICLE SPEED CONTROL
Potential Consequences:
When driving in highway traffic at moderate to high speeds (as well as low speeds), the truck will often accelerate with (and towards) a vehicle that is less than 1 second ahead of the truck. Certainly this often happens when there is not a safe distance between the truck and the next vehicle. The trucks systems in no way seem to expect that the next vehicle could slam on brakes at any moment. I have had this happen many times when a vehicle merges too close in front of me and then accelerates. The truck will accelerate with the vehicle (that the truck is now tailgating), even though there is slowing or stopping traffic directly ahead of the vehicle the truck is following. The Safety Director at Tyson Foods, Robert Carl, told me in a conference call about the unsafe flaws in the truck, that these Freightliner systems are programmed to "try" to maintain about a 2.5 second following distance. Even this is patently unsafe. Driver safety guidelines (FMCSA) are: "If you are driving below 40 mph, you should leave at least one second for every 10 feet of vehicle length. For a typical tractor-trailer, this results in 4 seconds between you and the leading vehicle. For speeds over 40 mph, you should leave one additional second." It would appear that Daimler/Freightliner may have used Autonomous Driving software that was designed for cars, and has tried to "adjust" it to work in tractor-trailers. That is speculation, but based on the supposed target following distance, that may be correct. 2.5 seconds is certainly too close, and the distances of less than 1 second that I have commonly seen are not acceptable in any truck.
Corrective Action:
When driving in highway traffic at moderate to high speeds (as well as low speeds), the truck will often accelerate with (and towards) a vehicle that is less than 1 second ahead of the truck. Certainly this often happens when there is not a safe distance between the truck and the next vehicle. The trucks systems in no way seem to expect that the next vehicle could slam on brakes at any moment. I have had this happen many times when a vehicle merges too close in front of me and then accelerates. The truck will accelerate with the vehicle (that the truck is now tailgating), even though there is slowing or stopping traffic directly ahead of the vehicle the truck is following. The Safety Director at Tyson Foods, Robert Carl, told me in a conference call about the unsafe flaws in the truck, that these Freightliner systems are programmed to "try" to maintain about a 2.5 second following distance. Even this is patently unsafe. Driver safety guidelines (FMCSA) are: "If you are driving below 40 mph, you should leave at least one second for every 10 feet of vehicle length. For a typical tractor-trailer, this results in 4 seconds between you and the leading vehicle. For speeds over 40 mph, you should leave one additional second." It would appear that Daimler/Freightliner may have used Autonomous Driving software that was designed for cars, and has tried to "adjust" it to work in tractor-trailers. That is speculation, but based on the supposed target following distance, that may be correct. 2.5 seconds is certainly too close, and the distances of less than 1 second that I have commonly seen are not acceptable in any truck.
Additional Notes:
When driving in highway traffic at moderate to high speeds (as well as low speeds), the truck will often accelerate with (and towards) a vehicle that is less than 1 second ahead of the truck. Certainly this often happens when there is not a safe distance between the truck and the next vehicle. The trucks systems in no way seem to expect that the next vehicle could slam on brakes at any moment. I have had this happen many times when a vehicle merges too close in front of me and then accelerates. The truck will accelerate with the vehicle (that the truck is now tailgating), even though there is slowing or stopping traffic directly ahead of the vehicle the truck is following. The Safety Director at Tyson Foods, Robert Carl, told me in a conference call about the unsafe flaws in the truck, that these Freightliner systems are programmed to "try" to maintain about a 2.5 second following distance. Even this is patently unsafe. Driver safety guidelines (FMCSA) are: "If you are driving below 40 mph, you should leave at least one second for every 10 feet of vehicle length. For a typical tractor-trailer, this results in 4 seconds between you and the leading vehicle. For speeds over 40 mph, you should leave one additional second." It would appear that Daimler/Freightliner may have used Autonomous Driving software that was designed for cars, and has tried to "adjust" it to work in tractor-trailers. That is speculation, but based on the supposed target following distance, that may be correct. 2.5 seconds is certainly too close, and the distances of less than 1 second that I have commonly seen are not acceptable in any truck.
Mfg Campaign: 11633132
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
Potential Consequences:
When driving in highway traffic at moderate to high speeds (as well as low speeds), the truck will often accelerate with (and towards) a vehicle that is less than 1 second ahead of the truck. Certainly this often happens when there is not a safe distance between the truck and the next vehicle. The trucks systems in no way seem to expect that the next vehicle could slam on brakes at any moment. I have had this happen many times when a vehicle merges too close in front of me and then accelerates. The truck will accelerate with the vehicle (that the truck is now tailgating), even though there is slowing or stopping traffic directly ahead of the vehicle the truck is following. The Safety Director at Tyson Foods, Robert Carl, told me in a conference call about the unsafe flaws in the truck, that these Freightliner systems are programmed to "try" to maintain about a 2.5 second following distance. Even this is patently unsafe. Driver safety guidelines (FMCSA) are: "If you are driving below 40 mph, you should leave at least one second for every 10 feet of vehicle length. For a typical tractor-trailer, this results in 4 seconds between you and the leading vehicle. For speeds over 40 mph, you should leave one additional second." It would appear that Daimler/Freightliner may have used Autonomous Driving software that was designed for cars, and has tried to "adjust" it to work in tractor-trailers. That is speculation, but based on the supposed target following distance, that may be correct. 2.5 seconds is certainly too close, and the distances of less than 1 second that I have commonly seen are not acceptable in any truck.
Corrective Action:
When driving in highway traffic at moderate to high speeds (as well as low speeds), the truck will often accelerate with (and towards) a vehicle that is less than 1 second ahead of the truck. Certainly this often happens when there is not a safe distance between the truck and the next vehicle. The trucks systems in no way seem to expect that the next vehicle could slam on brakes at any moment. I have had this happen many times when a vehicle merges too close in front of me and then accelerates. The truck will accelerate with the vehicle (that the truck is now tailgating), even though there is slowing or stopping traffic directly ahead of the vehicle the truck is following. The Safety Director at Tyson Foods, Robert Carl, told me in a conference call about the unsafe flaws in the truck, that these Freightliner systems are programmed to "try" to maintain about a 2.5 second following distance. Even this is patently unsafe. Driver safety guidelines (FMCSA) are: "If you are driving below 40 mph, you should leave at least one second for every 10 feet of vehicle length. For a typical tractor-trailer, this results in 4 seconds between you and the leading vehicle. For speeds over 40 mph, you should leave one additional second." It would appear that Daimler/Freightliner may have used Autonomous Driving software that was designed for cars, and has tried to "adjust" it to work in tractor-trailers. That is speculation, but based on the supposed target following distance, that may be correct. 2.5 seconds is certainly too close, and the distances of less than 1 second that I have commonly seen are not acceptable in any truck.
Additional Notes:
When driving in highway traffic at moderate to high speeds (as well as low speeds), the truck will often accelerate with (and towards) a vehicle that is less than 1 second ahead of the truck. Certainly this often happens when there is not a safe distance between the truck and the next vehicle. The trucks systems in no way seem to expect that the next vehicle could slam on brakes at any moment. I have had this happen many times when a vehicle merges too close in front of me and then accelerates. The truck will accelerate with the vehicle (that the truck is now tailgating), even though there is slowing or stopping traffic directly ahead of the vehicle the truck is following. The Safety Director at Tyson Foods, Robert Carl, told me in a conference call about the unsafe flaws in the truck, that these Freightliner systems are programmed to "try" to maintain about a 2.5 second following distance. Even this is patently unsafe. Driver safety guidelines (FMCSA) are: "If you are driving below 40 mph, you should leave at least one second for every 10 feet of vehicle length. For a typical tractor-trailer, this results in 4 seconds between you and the leading vehicle. For speeds over 40 mph, you should leave one additional second." It would appear that Daimler/Freightliner may have used Autonomous Driving software that was designed for cars, and has tried to "adjust" it to work in tractor-trailers. That is speculation, but based on the supposed target following distance, that may be correct. 2.5 seconds is certainly too close, and the distances of less than 1 second that I have commonly seen are not acceptable in any truck.
Mfg Campaign: 11633132
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING
Potential Consequences:
When driving in highway traffic at moderate to high speeds (as well as low speeds), the truck will often accelerate with (and towards) a vehicle that is less than 1 second ahead of the truck. Certainly this often happens when there is not a safe distance between the truck and the next vehicle. The trucks systems in no way seem to expect that the next vehicle could slam on brakes at any moment. I have had this happen many times when a vehicle merges too close in front of me and then accelerates. The truck will accelerate with the vehicle (that the truck is now tailgating), even though there is slowing or stopping traffic directly ahead of the vehicle the truck is following. The Safety Director at Tyson Foods, Robert Carl, told me in a conference call about the unsafe flaws in the truck, that these Freightliner systems are programmed to "try" to maintain about a 2.5 second following distance. Even this is patently unsafe. Driver safety guidelines (FMCSA) are: "If you are driving below 40 mph, you should leave at least one second for every 10 feet of vehicle length. For a typical tractor-trailer, this results in 4 seconds between you and the leading vehicle. For speeds over 40 mph, you should leave one additional second." It would appear that Daimler/Freightliner may have used Autonomous Driving software that was designed for cars, and has tried to "adjust" it to work in tractor-trailers. That is speculation, but based on the supposed target following distance, that may be correct. 2.5 seconds is certainly too close, and the distances of less than 1 second that I have commonly seen are not acceptable in any truck.
Corrective Action:
When driving in highway traffic at moderate to high speeds (as well as low speeds), the truck will often accelerate with (and towards) a vehicle that is less than 1 second ahead of the truck. Certainly this often happens when there is not a safe distance between the truck and the next vehicle. The trucks systems in no way seem to expect that the next vehicle could slam on brakes at any moment. I have had this happen many times when a vehicle merges too close in front of me and then accelerates. The truck will accelerate with the vehicle (that the truck is now tailgating), even though there is slowing or stopping traffic directly ahead of the vehicle the truck is following. The Safety Director at Tyson Foods, Robert Carl, told me in a conference call about the unsafe flaws in the truck, that these Freightliner systems are programmed to "try" to maintain about a 2.5 second following distance. Even this is patently unsafe. Driver safety guidelines (FMCSA) are: "If you are driving below 40 mph, you should leave at least one second for every 10 feet of vehicle length. For a typical tractor-trailer, this results in 4 seconds between you and the leading vehicle. For speeds over 40 mph, you should leave one additional second." It would appear that Daimler/Freightliner may have used Autonomous Driving software that was designed for cars, and has tried to "adjust" it to work in tractor-trailers. That is speculation, but based on the supposed target following distance, that may be correct. 2.5 seconds is certainly too close, and the distances of less than 1 second that I have commonly seen are not acceptable in any truck.
Additional Notes:
When driving in highway traffic at moderate to high speeds (as well as low speeds), the truck will often accelerate with (and towards) a vehicle that is less than 1 second ahead of the truck. Certainly this often happens when there is not a safe distance between the truck and the next vehicle. The trucks systems in no way seem to expect that the next vehicle could slam on brakes at any moment. I have had this happen many times when a vehicle merges too close in front of me and then accelerates. The truck will accelerate with the vehicle (that the truck is now tailgating), even though there is slowing or stopping traffic directly ahead of the vehicle the truck is following. The Safety Director at Tyson Foods, Robert Carl, told me in a conference call about the unsafe flaws in the truck, that these Freightliner systems are programmed to "try" to maintain about a 2.5 second following distance. Even this is patently unsafe. Driver safety guidelines (FMCSA) are: "If you are driving below 40 mph, you should leave at least one second for every 10 feet of vehicle length. For a typical tractor-trailer, this results in 4 seconds between you and the leading vehicle. For speeds over 40 mph, you should leave one additional second." It would appear that Daimler/Freightliner may have used Autonomous Driving software that was designed for cars, and has tried to "adjust" it to work in tractor-trailers. That is speculation, but based on the supposed target following distance, that may be correct. 2.5 seconds is certainly too close, and the distances of less than 1 second that I have commonly seen are not acceptable in any truck.
Mfg Campaign: 11633132
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING
Potential Consequences:
When a vehicle is merging into my lane, the truck will often not detect or react to the encroaching vehicle; this happens even when there is plenty of space, and the encroaching vehicle is halfway into my lane. I have had to intervene several times, since the truck was accelerating toward the previous vehicle in my headway, and ingoring the intervening merging vehicle. In contrast, the sensors in the truck apparently can see when a vehicle is near to the front, and mostly out of the headway of the truck (only part of the front vehicle in my lane, like when exiting). This truck will brake, and continue braking unnecessarily (and unnecessarily hard braking) for a vehicle that is completely out of my lane (by several feet), before continuing and regaining speed. This shows that the sensors are capable of "seeing" and tracking the vechicles, but still does not respond to traffic merging into the truck's headway.
Corrective Action:
When a vehicle is merging into my lane, the truck will often not detect or react to the encroaching vehicle; this happens even when there is plenty of space, and the encroaching vehicle is halfway into my lane. I have had to intervene several times, since the truck was accelerating toward the previous vehicle in my headway, and ingoring the intervening merging vehicle. In contrast, the sensors in the truck apparently can see when a vehicle is near to the front, and mostly out of the headway of the truck (only part of the front vehicle in my lane, like when exiting). This truck will brake, and continue braking unnecessarily (and unnecessarily hard braking) for a vehicle that is completely out of my lane (by several feet), before continuing and regaining speed. This shows that the sensors are capable of "seeing" and tracking the vechicles, but still does not respond to traffic merging into the truck's headway.
Additional Notes:
When a vehicle is merging into my lane, the truck will often not detect or react to the encroaching vehicle; this happens even when there is plenty of space, and the encroaching vehicle is halfway into my lane. I have had to intervene several times, since the truck was accelerating toward the previous vehicle in my headway, and ingoring the intervening merging vehicle. In contrast, the sensors in the truck apparently can see when a vehicle is near to the front, and mostly out of the headway of the truck (only part of the front vehicle in my lane, like when exiting). This truck will brake, and continue braking unnecessarily (and unnecessarily hard braking) for a vehicle that is completely out of my lane (by several feet), before continuing and regaining speed. This shows that the sensors are capable of "seeing" and tracking the vechicles, but still does not respond to traffic merging into the truck's headway.
Mfg Campaign: 11633136
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
FORWARD COLLISION AVOIDANCE: WARNINGS
Potential Consequences:
When a vehicle is merging into my lane, the truck will often not detect or react to the encroaching vehicle; this happens even when there is plenty of space, and the encroaching vehicle is halfway into my lane. I have had to intervene several times, since the truck was accelerating toward the previous vehicle in my headway, and ingoring the intervening merging vehicle. In contrast, the sensors in the truck apparently can see when a vehicle is near to the front, and mostly out of the headway of the truck (only part of the front vehicle in my lane, like when exiting). This truck will brake, and continue braking unnecessarily (and unnecessarily hard braking) for a vehicle that is completely out of my lane (by several feet), before continuing and regaining speed. This shows that the sensors are capable of "seeing" and tracking the vechicles, but still does not respond to traffic merging into the truck's headway.
Corrective Action:
When a vehicle is merging into my lane, the truck will often not detect or react to the encroaching vehicle; this happens even when there is plenty of space, and the encroaching vehicle is halfway into my lane. I have had to intervene several times, since the truck was accelerating toward the previous vehicle in my headway, and ingoring the intervening merging vehicle. In contrast, the sensors in the truck apparently can see when a vehicle is near to the front, and mostly out of the headway of the truck (only part of the front vehicle in my lane, like when exiting). This truck will brake, and continue braking unnecessarily (and unnecessarily hard braking) for a vehicle that is completely out of my lane (by several feet), before continuing and regaining speed. This shows that the sensors are capable of "seeing" and tracking the vechicles, but still does not respond to traffic merging into the truck's headway.
Additional Notes:
When a vehicle is merging into my lane, the truck will often not detect or react to the encroaching vehicle; this happens even when there is plenty of space, and the encroaching vehicle is halfway into my lane. I have had to intervene several times, since the truck was accelerating toward the previous vehicle in my headway, and ingoring the intervening merging vehicle. In contrast, the sensors in the truck apparently can see when a vehicle is near to the front, and mostly out of the headway of the truck (only part of the front vehicle in my lane, like when exiting). This truck will brake, and continue braking unnecessarily (and unnecessarily hard braking) for a vehicle that is completely out of my lane (by several feet), before continuing and regaining speed. This shows that the sensors are capable of "seeing" and tracking the vechicles, but still does not respond to traffic merging into the truck's headway.
Mfg Campaign: 11633136
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
VEHICLE SPEED CONTROL
Potential Consequences:
When a vehicle is merging into my lane, the truck will often not detect or react to the encroaching vehicle; this happens even when there is plenty of space, and the encroaching vehicle is halfway into my lane. I have had to intervene several times, since the truck was accelerating toward the previous vehicle in my headway, and ingoring the intervening merging vehicle. In contrast, the sensors in the truck apparently can see when a vehicle is near to the front, and mostly out of the headway of the truck (only part of the front vehicle in my lane, like when exiting). This truck will brake, and continue braking unnecessarily (and unnecessarily hard braking) for a vehicle that is completely out of my lane (by several feet), before continuing and regaining speed. This shows that the sensors are capable of "seeing" and tracking the vechicles, but still does not respond to traffic merging into the truck's headway.
Corrective Action:
When a vehicle is merging into my lane, the truck will often not detect or react to the encroaching vehicle; this happens even when there is plenty of space, and the encroaching vehicle is halfway into my lane. I have had to intervene several times, since the truck was accelerating toward the previous vehicle in my headway, and ingoring the intervening merging vehicle. In contrast, the sensors in the truck apparently can see when a vehicle is near to the front, and mostly out of the headway of the truck (only part of the front vehicle in my lane, like when exiting). This truck will brake, and continue braking unnecessarily (and unnecessarily hard braking) for a vehicle that is completely out of my lane (by several feet), before continuing and regaining speed. This shows that the sensors are capable of "seeing" and tracking the vechicles, but still does not respond to traffic merging into the truck's headway.
Additional Notes:
When a vehicle is merging into my lane, the truck will often not detect or react to the encroaching vehicle; this happens even when there is plenty of space, and the encroaching vehicle is halfway into my lane. I have had to intervene several times, since the truck was accelerating toward the previous vehicle in my headway, and ingoring the intervening merging vehicle. In contrast, the sensors in the truck apparently can see when a vehicle is near to the front, and mostly out of the headway of the truck (only part of the front vehicle in my lane, like when exiting). This truck will brake, and continue braking unnecessarily (and unnecessarily hard braking) for a vehicle that is completely out of my lane (by several feet), before continuing and regaining speed. This shows that the sensors are capable of "seeing" and tracking the vechicles, but still does not respond to traffic merging into the truck's headway.
Mfg Campaign: 11633136
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
VEHICLE SPEED CONTROL
Potential Consequences:
These trucks have a non-adjustable default setting for Over and Under cruise control speed setting. This means, in the case of the truck I drove, that the cruise control will allow the truck to go 5 mph over the set speed before engaging the engine brake, or 4 mph under the setting before accelerating. The problem is that when set for the speed limit, the truck will climb to 7 mph over the set speed before engaging engine brake. When driving on a downgrade with a lot of weight, the truck quickly gets to well over a safe speed before the truck will attempt to slow down. This often results in an overspeed situation when approaching curves. In older models of Freightliner, and maybe in current versions that are adjustable, there is a setting to change this to closer to the set speed. In this model, or large companies' ordered versions, this adjustment is not available. The idea is to save fuel by "hyper-mile" style of driving. It makes for an unpredictable speed of vehicle, frustrating other drivers, and sometimes leading to unsafe overspeed situations.
Corrective Action:
These trucks have a non-adjustable default setting for Over and Under cruise control speed setting. This means, in the case of the truck I drove, that the cruise control will allow the truck to go 5 mph over the set speed before engaging the engine brake, or 4 mph under the setting before accelerating. The problem is that when set for the speed limit, the truck will climb to 7 mph over the set speed before engaging engine brake. When driving on a downgrade with a lot of weight, the truck quickly gets to well over a safe speed before the truck will attempt to slow down. This often results in an overspeed situation when approaching curves. In older models of Freightliner, and maybe in current versions that are adjustable, there is a setting to change this to closer to the set speed. In this model, or large companies' ordered versions, this adjustment is not available. The idea is to save fuel by "hyper-mile" style of driving. It makes for an unpredictable speed of vehicle, frustrating other drivers, and sometimes leading to unsafe overspeed situations.
Additional Notes:
These trucks have a non-adjustable default setting for Over and Under cruise control speed setting. This means, in the case of the truck I drove, that the cruise control will allow the truck to go 5 mph over the set speed before engaging the engine brake, or 4 mph under the setting before accelerating. The problem is that when set for the speed limit, the truck will climb to 7 mph over the set speed before engaging engine brake. When driving on a downgrade with a lot of weight, the truck quickly gets to well over a safe speed before the truck will attempt to slow down. This often results in an overspeed situation when approaching curves. In older models of Freightliner, and maybe in current versions that are adjustable, there is a setting to change this to closer to the set speed. In this model, or large companies' ordered versions, this adjustment is not available. The idea is to save fuel by "hyper-mile" style of driving. It makes for an unpredictable speed of vehicle, frustrating other drivers, and sometimes leading to unsafe overspeed situations.
Mfg Campaign: 11633138
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
Potential Consequences:
These trucks have a non-adjustable default setting for Over and Under cruise control speed setting. This means, in the case of the truck I drove, that the cruise control will allow the truck to go 5 mph over the set speed before engaging the engine brake, or 4 mph under the setting before accelerating. The problem is that when set for the speed limit, the truck will climb to 7 mph over the set speed before engaging engine brake. When driving on a downgrade with a lot of weight, the truck quickly gets to well over a safe speed before the truck will attempt to slow down. This often results in an overspeed situation when approaching curves. In older models of Freightliner, and maybe in current versions that are adjustable, there is a setting to change this to closer to the set speed. In this model, or large companies' ordered versions, this adjustment is not available. The idea is to save fuel by "hyper-mile" style of driving. It makes for an unpredictable speed of vehicle, frustrating other drivers, and sometimes leading to unsafe overspeed situations.
Corrective Action:
These trucks have a non-adjustable default setting for Over and Under cruise control speed setting. This means, in the case of the truck I drove, that the cruise control will allow the truck to go 5 mph over the set speed before engaging the engine brake, or 4 mph under the setting before accelerating. The problem is that when set for the speed limit, the truck will climb to 7 mph over the set speed before engaging engine brake. When driving on a downgrade with a lot of weight, the truck quickly gets to well over a safe speed before the truck will attempt to slow down. This often results in an overspeed situation when approaching curves. In older models of Freightliner, and maybe in current versions that are adjustable, there is a setting to change this to closer to the set speed. In this model, or large companies' ordered versions, this adjustment is not available. The idea is to save fuel by "hyper-mile" style of driving. It makes for an unpredictable speed of vehicle, frustrating other drivers, and sometimes leading to unsafe overspeed situations.
Additional Notes:
These trucks have a non-adjustable default setting for Over and Under cruise control speed setting. This means, in the case of the truck I drove, that the cruise control will allow the truck to go 5 mph over the set speed before engaging the engine brake, or 4 mph under the setting before accelerating. The problem is that when set for the speed limit, the truck will climb to 7 mph over the set speed before engaging engine brake. When driving on a downgrade with a lot of weight, the truck quickly gets to well over a safe speed before the truck will attempt to slow down. This often results in an overspeed situation when approaching curves. In older models of Freightliner, and maybe in current versions that are adjustable, there is a setting to change this to closer to the set speed. In this model, or large companies' ordered versions, this adjustment is not available. The idea is to save fuel by "hyper-mile" style of driving. It makes for an unpredictable speed of vehicle, frustrating other drivers, and sometimes leading to unsafe overspeed situations.
Mfg Campaign: 11633138
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
VEHICLE SPEED CONTROL
Potential Consequences:
Complaint 1 When using cruise control in 2024 Freightliner Cascadia trucks with level 2 autonomous driving features, there is no option to turn off the autonomous driving features (and use standard cruise control); the driver is forced to use the system if he wants or needs to use cruise control. This apparently is a software setting that is available in some versions, but is not available in models bought/leased to large trucking companies. Complaint 2 There is no way to adjust the "agressiveness" of the self-driving (acceleration and braking) feature of these trucks. The default in this model truck is unknown to me, but in slow-and-go or stop-and-go traffic, the truck is highly aggressive; the truck follows too close very often, and waits until the last second to slow or stop in most cases. This also happens in high volume, higher speed traffic.
Corrective Action:
Complaint 1 When using cruise control in 2024 Freightliner Cascadia trucks with level 2 autonomous driving features, there is no option to turn off the autonomous driving features (and use standard cruise control); the driver is forced to use the system if he wants or needs to use cruise control. This apparently is a software setting that is available in some versions, but is not available in models bought/leased to large trucking companies. Complaint 2 There is no way to adjust the "agressiveness" of the self-driving (acceleration and braking) feature of these trucks. The default in this model truck is unknown to me, but in slow-and-go or stop-and-go traffic, the truck is highly aggressive; the truck follows too close very often, and waits until the last second to slow or stop in most cases. This also happens in high volume, higher speed traffic.
Additional Notes:
Complaint 1 When using cruise control in 2024 Freightliner Cascadia trucks with level 2 autonomous driving features, there is no option to turn off the autonomous driving features (and use standard cruise control); the driver is forced to use the system if he wants or needs to use cruise control. This apparently is a software setting that is available in some versions, but is not available in models bought/leased to large trucking companies. Complaint 2 There is no way to adjust the "agressiveness" of the self-driving (acceleration and braking) feature of these trucks. The default in this model truck is unknown to me, but in slow-and-go or stop-and-go traffic, the truck is highly aggressive; the truck follows too close very often, and waits until the last second to slow or stop in most cases. This also happens in high volume, higher speed traffic.
Mfg Campaign: 11633141
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
Potential Consequences:
Complaint 1 When using cruise control in 2024 Freightliner Cascadia trucks with level 2 autonomous driving features, there is no option to turn off the autonomous driving features (and use standard cruise control); the driver is forced to use the system if he wants or needs to use cruise control. This apparently is a software setting that is available in some versions, but is not available in models bought/leased to large trucking companies. Complaint 2 There is no way to adjust the "agressiveness" of the self-driving (acceleration and braking) feature of these trucks. The default in this model truck is unknown to me, but in slow-and-go or stop-and-go traffic, the truck is highly aggressive; the truck follows too close very often, and waits until the last second to slow or stop in most cases. This also happens in high volume, higher speed traffic.
Corrective Action:
Complaint 1 When using cruise control in 2024 Freightliner Cascadia trucks with level 2 autonomous driving features, there is no option to turn off the autonomous driving features (and use standard cruise control); the driver is forced to use the system if he wants or needs to use cruise control. This apparently is a software setting that is available in some versions, but is not available in models bought/leased to large trucking companies. Complaint 2 There is no way to adjust the "agressiveness" of the self-driving (acceleration and braking) feature of these trucks. The default in this model truck is unknown to me, but in slow-and-go or stop-and-go traffic, the truck is highly aggressive; the truck follows too close very often, and waits until the last second to slow or stop in most cases. This also happens in high volume, higher speed traffic.
Additional Notes:
Complaint 1 When using cruise control in 2024 Freightliner Cascadia trucks with level 2 autonomous driving features, there is no option to turn off the autonomous driving features (and use standard cruise control); the driver is forced to use the system if he wants or needs to use cruise control. This apparently is a software setting that is available in some versions, but is not available in models bought/leased to large trucking companies. Complaint 2 There is no way to adjust the "agressiveness" of the self-driving (acceleration and braking) feature of these trucks. The default in this model truck is unknown to me, but in slow-and-go or stop-and-go traffic, the truck is highly aggressive; the truck follows too close very often, and waits until the last second to slow or stop in most cases. This also happens in high volume, higher speed traffic.
Mfg Campaign: 11633141
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
VEHICLE SPEED CONTROL
Potential Consequences:
The cruise control has been programmed to stay engaged, in many instances, after the driver has used the foot brake. In some situations, like approaching a traffic circle, I have slowed down with the foot brake, then had the truck unexpectedly start to accelerate after I released the brake. This apparently has to do with a vehicle in my headway allowing the cruise to remain engaged, and then after the vehicle leaves my headway the truck thinks it can accelerate again. There is never a good reason for the cruise control in any vehicle to remain engaged after using the brakes. This results in unpredicted situations, like unplanned acceleration. This also applies to vehicles trying to merge in front of me, where I use the brakes to back off some and allow them in, but then the cruise (still engaged) will accelerate again toward the vehicle that was previously in my headway.
Corrective Action:
The cruise control has been programmed to stay engaged, in many instances, after the driver has used the foot brake. In some situations, like approaching a traffic circle, I have slowed down with the foot brake, then had the truck unexpectedly start to accelerate after I released the brake. This apparently has to do with a vehicle in my headway allowing the cruise to remain engaged, and then after the vehicle leaves my headway the truck thinks it can accelerate again. There is never a good reason for the cruise control in any vehicle to remain engaged after using the brakes. This results in unpredicted situations, like unplanned acceleration. This also applies to vehicles trying to merge in front of me, where I use the brakes to back off some and allow them in, but then the cruise (still engaged) will accelerate again toward the vehicle that was previously in my headway.
Additional Notes:
The cruise control has been programmed to stay engaged, in many instances, after the driver has used the foot brake. In some situations, like approaching a traffic circle, I have slowed down with the foot brake, then had the truck unexpectedly start to accelerate after I released the brake. This apparently has to do with a vehicle in my headway allowing the cruise to remain engaged, and then after the vehicle leaves my headway the truck thinks it can accelerate again. There is never a good reason for the cruise control in any vehicle to remain engaged after using the brakes. This results in unpredicted situations, like unplanned acceleration. This also applies to vehicles trying to merge in front of me, where I use the brakes to back off some and allow them in, but then the cruise (still engaged) will accelerate again toward the vehicle that was previously in my headway.
Mfg Campaign: 11633142
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
Potential Consequences:
The cruise control has been programmed to stay engaged, in many instances, after the driver has used the foot brake. In some situations, like approaching a traffic circle, I have slowed down with the foot brake, then had the truck unexpectedly start to accelerate after I released the brake. This apparently has to do with a vehicle in my headway allowing the cruise to remain engaged, and then after the vehicle leaves my headway the truck thinks it can accelerate again. There is never a good reason for the cruise control in any vehicle to remain engaged after using the brakes. This results in unpredicted situations, like unplanned acceleration. This also applies to vehicles trying to merge in front of me, where I use the brakes to back off some and allow them in, but then the cruise (still engaged) will accelerate again toward the vehicle that was previously in my headway.
Corrective Action:
The cruise control has been programmed to stay engaged, in many instances, after the driver has used the foot brake. In some situations, like approaching a traffic circle, I have slowed down with the foot brake, then had the truck unexpectedly start to accelerate after I released the brake. This apparently has to do with a vehicle in my headway allowing the cruise to remain engaged, and then after the vehicle leaves my headway the truck thinks it can accelerate again. There is never a good reason for the cruise control in any vehicle to remain engaged after using the brakes. This results in unpredicted situations, like unplanned acceleration. This also applies to vehicles trying to merge in front of me, where I use the brakes to back off some and allow them in, but then the cruise (still engaged) will accelerate again toward the vehicle that was previously in my headway.
Additional Notes:
The cruise control has been programmed to stay engaged, in many instances, after the driver has used the foot brake. In some situations, like approaching a traffic circle, I have slowed down with the foot brake, then had the truck unexpectedly start to accelerate after I released the brake. This apparently has to do with a vehicle in my headway allowing the cruise to remain engaged, and then after the vehicle leaves my headway the truck thinks it can accelerate again. There is never a good reason for the cruise control in any vehicle to remain engaged after using the brakes. This results in unpredicted situations, like unplanned acceleration. This also applies to vehicles trying to merge in front of me, where I use the brakes to back off some and allow them in, but then the cruise (still engaged) will accelerate again toward the vehicle that was previously in my headway.
Mfg Campaign: 11633142
Recall Date: Dec 30, 2024
Daimler Trucks North America, Llc
Defect Description:
SUSPENSION
Potential Consequences:
It is hard to impossible to drive the truck in a straight line (compared to models without the smartvalves), and often drifts side to side randomly without any warning or feedback. The steering requires constant input, and the "feel" of the truck is not correct to allow intuitive steering. When driving in tight areas, I find that I need to stay at least a foot away from barriers or other objects to not be in danger of hitting them. When in width-limited areas, like construction zones, I often need to straddle the center line and block other vehicles from passing me, so as not to be in danger of collision. These controllability problems are induced by the "active" smartvalve system. This is the chassis leveling system that adjusts air to the suspension air springs (air bags). The smart valve system is there to allow a driver to adjust the suspension up or down as needed to assist in hooking in improperly positioned trailer (to prevent injuries). The system also actively interferes with what would be the normal operation of a suspension "leveling" valve, and adjusts and or blocks the normal flow of air in and out of the suspension when driving. This results in poor handling and control problems. I have asked to have the valve replaced with a normal "dumb" valve on my truck, since I have found that the trucks handle normally with a standard leveling valve. I have also found that in many curvy road situations, the truck is hard to keep from running off the road, even bobtail. There is severe apparent understeer, and it seems likely to be attributed to the smartvalve leveler interfering with the suspension. I see that there is a recall on Freightliners having to do with understeer problems on curves (Recall 234245 [USA]: Understeering during a j-turn may increase the risk of a crash.). The recall says that Freightliner will replace the tires; it is likely that this will not help in the case of models with an active "smartvalve" system.
Corrective Action:
It is hard to impossible to drive the truck in a straight line (compared to models without the smartvalves), and often drifts side to side randomly without any warning or feedback. The steering requires constant input, and the "feel" of the truck is not correct to allow intuitive steering. When driving in tight areas, I find that I need to stay at least a foot away from barriers or other objects to not be in danger of hitting them. When in width-limited areas, like construction zones, I often need to straddle the center line and block other vehicles from passing me, so as not to be in danger of collision. These controllability problems are induced by the "active" smartvalve system. This is the chassis leveling system that adjusts air to the suspension air springs (air bags). The smart valve system is there to allow a driver to adjust the suspension up or down as needed to assist in hooking in improperly positioned trailer (to prevent injuries). The system also actively interferes with what would be the normal operation of a suspension "leveling" valve, and adjusts and or blocks the normal flow of air in and out of the suspension when driving. This results in poor handling and control problems. I have asked to have the valve replaced with a normal "dumb" valve on my truck, since I have found that the trucks handle normally with a standard leveling valve. I have also found that in many curvy road situations, the truck is hard to keep from running off the road, even bobtail. There is severe apparent understeer, and it seems likely to be attributed to the smartvalve leveler interfering with the suspension. I see that there is a recall on Freightliners having to do with understeer problems on curves (Recall 234245 [USA]: Understeering during a j-turn may increase the risk of a crash.). The recall says that Freightliner will replace the tires; it is likely that this will not help in the case of models with an active "smartvalve" system.
Additional Notes:
It is hard to impossible to drive the truck in a straight line (compared to models without the smartvalves), and often drifts side to side randomly without any warning or feedback. The steering requires constant input, and the "feel" of the truck is not correct to allow intuitive steering. When driving in tight areas, I find that I need to stay at least a foot away from barriers or other objects to not be in danger of hitting them. When in width-limited areas, like construction zones, I often need to straddle the center line and block other vehicles from passing me, so as not to be in danger of collision. These controllability problems are induced by the "active" smartvalve system. This is the chassis leveling system that adjusts air to the suspension air springs (air bags). The smart valve system is there to allow a driver to adjust the suspension up or down as needed to assist in hooking in improperly positioned trailer (to prevent injuries). The system also actively interferes with what would be the normal operation of a suspension "leveling" valve, and adjusts and or blocks the normal flow of air in and out of the suspension when driving. This results in poor handling and control problems. I have asked to have the valve replaced with a normal "dumb" valve on my truck, since I have found that the trucks handle normally with a standard leveling valve. I have also found that in many curvy road situations, the truck is hard to keep from running off the road, even bobtail. There is severe apparent understeer, and it seems likely to be attributed to the smartvalve leveler interfering with the suspension. I see that there is a recall on Freightliners having to do with understeer problems on curves (Recall 234245 [USA]: Understeering during a j-turn may increase the risk of a crash.). The recall says that Freightliner will replace the tires; it is likely that this will not help in the case of models with an active "smartvalve" system.
Mfg Campaign: 11633144
Recall Date: Dec 30, 2024
Need Legal Help?
Featured Attorneys
Barry Edzant
Edzant Price LLC
Valencia, CA • 36 yrs
Focus: Lemon Law, Personal Injury
Recent Articles
Jeep Grand Cherokee Head Restraint Problem
Chrysler (FCA US, LLC) has announced a safety issue affecting certain 2023–2024 Jeep Grand Ch ...
Aug 1, 2025Fuel Injector Problem: 2021-2024 Ford Bronco Sport and 2020-2022 Ford Escape
If you own a 2021-2024 Ford Bronco Sport or 2020-2022 Ford Escape equipped with a 1.5L Dragon GTDI e ...
Jul 28, 2025Airbag Problem Affects 2022-2025 Chrysler Pacifica and Voyager Vehicles
If you own a Chrysler Pacifica or Voyager, your vehicle may be equipped with defective side curtain ...
Jul 24, 2025